From: Good Guy Date: Fri, 26 Jan 2024 23:26:59 +0000 (-0700) Subject: Credit Andrew/Andrea for defing procedure and putting into Latex format X-Git-Tag: 2024-01~2 X-Git-Url: https://git.cinelerra-gg.org/git/?a=commitdiff_plain;h=18c6fb015ed4409ffe760a9d91a0f5934f2927ce;p=goodguy%2Fcin-manual-latex.git Credit Andrew/Andrea for defing procedure and putting into Latex format --- diff --git a/parts/DVD.tex b/parts/DVD.tex index 5d38c8d..1238927 100644 --- a/parts/DVD.tex +++ b/parts/DVD.tex @@ -502,6 +502,48 @@ because the upsampling of interlaced chroma fields is normally done using a prog With this mode enabled, the MPEG decoder uses a different algorithm for interlaced frames so that the 4:2:0 format chroma interlacing is preserved. +\section{DVD with LPCM audio}% +\label{sec:dvd_lpcm_audio} + +By default, the audio when creating a DVD is always \textit{AC3}. However you can switch to \textit{PCM} (Pulse Code Modulator) with just a few additional steps as outlined below. +Note that Audio must be $48Khz$ or $96Khz$, nothing else is supported, even by ffmpeg's dvd pcm encoder. + +\begin{enumerate} + \item Start \CGG{} from a terminal window so you will be able to see what is happening. Only the final step when you actually want to write to a +DVD media writer, requires privileges of either root or the system has +granted the user this privilege. + \item Make sure you have your video with audio loaded and edited to your satisfaction and you are positioned at the start of the video. + \item Use the \texttt{File} pulldown and select the \textit{DVD Render} option. + \item In the\textit{Create DVD} window, accept the defaults or select different values and then click \texttt{OK}. Do not check "Use FFMPEG" as that will not work. + \item When the \textit{Batch Render} window pops up, in the big box towards the bottom will be 2 lines with the first line for \textit{Video} already highlighted. Instead, click on the second line, which is for \textit{Audio}, so that it is highlighted. + \item On the top left, you will see the \textit{File Format} set as AC3. Use the down arrow next to the box and change it to \textit{Raw PCM} by clicking on it. + \item When you switch to Raw PCM, you see the extension in the \texttt{Output path} above change to pcm + instead of ac3. Now just reset the extension from pcm to lpcm as that is required. In most cases if you click on the \texttt{Audio} wrench to see the settings, you will find that the standard settings of 16 bit Linear / Signed / Hi Lo work. If not, experiment for alternatives. + \item Now click on the \texttt{Start} box in the bottom left hand corner and \CGG{} will process what it can of the job and put you back at your terminal startup window. + \item You will see a few lines of output, some of which are shown below, to include the ERROR: + \begin{lstlisting}[style=sh] + running /dev/shm//dvd_20240116-182336/dvd.sh + INFO: [mplex] mplex version 2.1.0 (2.2.7 $Date: 2012/11/17 01:55:16 $) + **ERROR: [mplex] Unable to open file + /dev/shm/dvd_20240116-182336/dvd.ac3 for reading. + \end{lstlisting} + \item Change directory to the location as shown on the terminal window of \texttt{dvd.sh}. + \item Using an editor, modify the line in dvd.sh to change \texttt{dvd.ac3} to \texttt{dvd.lpcm} and change the mplex parameter to include: + \begin{lstlisting}[style=sh] + -L 48000:2:16 + \end{lstlisting} + The full line will look like this: + \begin{lstlisting}[style=sh] + mplex -f 8 -L 48000:2:16 -o $dir/dvd.mpg $dir/dvd.m2v $dir/dvd.lpcm + \end{lstlisting} + \item Now the script is ready to run in the same manner it would have had it been ac3. That is just run via: + \begin{lstlisting}[style=sh] + ./dvd.sh + \end{lstlisting} + \item Check to make sure there are no errors in the output shown on the window and proceed as usual. +\end{enumerate} + + \section{MPEG utility programs}% \label{sec:mpeg_utility_programs}