\section{Hardware video acceleration}%
\label{sec:hardware_video_acceleration}
+\index{hardware!acceleration}
With certain newer, more powerful graphics boards and newer device drivers, there is the potential for enhanced \textit{decode} and \textit{encode} performance. Decode refers to loading and playing video in \CGG{}. The GPU, Graphics Processing Unit, on the graphics board is accessed via one of the following libraries: vdpau or vaapi. The hardware acceleration done by the graphics card increases performance by activating certain functions in connection with a few of the FFmpeg decoders. This use makes it possible for the graphics card to decode video, thus offloading the CPU. Decode operations are described here next.
Encode refers to rendering video and is described at the end of this section
VA-API, Video Acceleration API, is an open source library which provides both hardware accelerated video encoding and decoding for use mostly with Intel (and AMD) graphics boards.
-Currently only the most common codecs, such as MPEG-1, MPEG-2, MPEG-4, and H.264 /MPEG-4, are accelerated/optimized by the graphics card to play these particular video formats efficiently. The other formats are not optimized so you will see no performance improvement since the CPU will handle them as before, just as if no hardware acceleration was activated. There are many different graphics cards and computer systems setup, so you will have to test which specific settings work best for you. So far this has been tested at least with Nvidia, Radeon, and Broadwell graphics boards on some AMD and Intel computers; depending on the graphics card, two to ten times higher processing speeds can be achieved. However, most graphic operations are single-threaded so that
-performing the operations in the hardware may actually be slower than in software making use of multiple CPUs, which frequently multi-thread many operations simultaneously.
+
+Currently only the most common codecs, such as MPEG-1, MPEG-2, MPEG-4, H.264 /MPEG-4 and h265 (hevc), are accelerated/optimized by the graphics card to play these particular video formats efficiently. The other formats are not optimized so you will see no performance improvement since the CPU will handle them as before, just as if no hardware acceleration was activated. There are many different graphics cards and computer systems setup, so you will have to test which specific settings work best for you. So far this has been tested at least with Nvidia, Radeon, and Broadwell graphics boards on some AMD and Intel computers; depending on the graphics card, two to ten times higher processing speeds can be achieved. However, most graphic operations are single-threaded so that performing the operations in the hardware may actually be slower than in software making use of multiple CPUs, which frequently multi-thread many operations simultaneously.
\subsection{GPU hardware decoding}%
\label{sub:gpu_hardware_decoding}
+\index{hardware!decoding}
\begin{enumerate}
\item Verify that you have installed \textit{libva-dev} or \textit{libva} on your operating system.
\subsubsection*{Special .opts file}%
\label{ssub:special_opts_file}
+\index{hardware!special opts files}
The situation may arise where you have enabled hardware acceleration and after loading several files for a project, you find that a file had some kind of error resulting in a black video instead of an image or you see an error message pop up which states something like \textit{Error retrieving data from GPU to CPU} or \textit{err: Unknown error occurred}. Because the \texttt{CIN\_HW\_DEV} environment variable is either all or none, ordinarily in order to correct the non-working video you would have to turn off hardware acceleration for the entire project/session. However, there is a way to continue working on your project without having to reload all of your files. You still use the environment variable and it will be effective for all of the formats it is able to handle, but you make an exception for any of the files that erred out. To do this you simply create a file in the same directory with the same name as the erring file with the different extension of .opts. The contents of this .opts file would just be the one line of:
\subsection{GPU hardware encoding}%
\label{sub:gpu_hardware_encoding}
+\index{hardware!encoding}
Encoding using hardware acceleration of your graphics board GPU is
included in \CGG{} but it is of limited availability and works only
\subsubsection*{Broadcom, Intel HD, AMD}%
\label{ssub:broadcom_intel_amd}
+\index{hardware!vaapi}
To use hardware acceleration for rendering (that is, encoding) you do not have to set a preference or an environment variable, as was required for decoding. To use this feature you use an ffmpeg render options file which specifies a vaapi codec, such as h264\_vaapi. You must include this line in that options file to trigger the hardware probe: \qquad \texttt{CIN\_HW\_DEV=vaapi}
\end{description}
Other option files can be added as needed for your specific hardware if it is known to work for you, such as VP8 and VP9. An example of the included \CGG{}’s \texttt{ffmpeg/video/h264\_vaapi.mp4} file (figure~\ref{fig:render-vaapi}):
-
-\begin{lstlisting}[numbers=none]
-mp4 h264_vaapi
-cin_hw_dev=vaapi
-profile=high
-\end{lstlisting}
-
\begin{figure}[htpb]
\centering
\includegraphics[width=1.0\linewidth]{render-vaapi.png}
\label{fig:render-vaapi}
\end{figure}
+\begin{lstlisting}[numbers=none]
+mp4 h264_vaapi
+cin_hw_dev=vaapi
+profile=high
+\end{lstlisting}
+
According to an online wiki, hardware encoders usually create output of lower quality than some software encoders like x264, but are much faster and use less CPU. Keep this in mind as you might want to set a higher bitrate to get output of similar visual quality.
Results of a particular test case performed on a Intel, 4-core computer, with Broadwell Graphics using an mp4 input video/audio file with dimensions of
\subsubsection*{Nvidia graphics boards}%
\label{ssub:nvidia_graphics_card}
+\index{hardware!nvenc}
To use hardware acceleration for rendering (that is, encoding) you do not have to set a preference or an environment variable, as was required for decoding. To use this feature you use an ffmpeg render options file which specifies the nvenc codec, either \texttt{h264\_nvenc.mp4} or \texttt{nvenc.mp4}. There are several requirements in order for this to work on your computer as listed here:
\subsection{Effects (OpenCL, Cuda)}%
\label{sub:effects_opencl_cuda}
+\index{openCL}
+\index{CUDA}
CUDA® is a parallel computing platform / programming model developed by Nvidia that provides big increases in computing performance through use of the GPU. It was first introduced in about 2006 for applications in computationally intense fields such as astronomy, biology, chemistry, and physics.
\section{Optimized Playback -- X11 Direct}%
\label{sec:optimized_playback}
+\index{playback -X11 direct}
Normally, when \CGG{} reads a video frame, it is copied into a \textit{Vframe}. This frame may also need other actions performed on it, such as a color model change. In addition, ffmpeg and libzmpeg \textit{can\_scale\_input}. So the read can be color transformed and scaled just by asking the library to do that. This means that if the compositor is in a \textit{good} state with no zoom, the VFrame read can be done in the fastest render color model, and already scaled to the correct size for the compositor. In reality, this is not what you need for editing, but quite often the \textit{virtualconsole} is not used because the render is media only -- that is \textit{just data}. If no data transforms are needed and the input scaling can be done, the vrender program detects this, and tells the codec to transmit the data in a compatible way to the compositor canvas. This is the \textit{X11 direct} data path.
\section{Proxy Settings and Transcode}%
\label{sec:proxy_settings}
-Working with videos that have large image geometry can greatly impede editing. Instead you can substitute \textit{proxies} which will create smaller video image files from the original file that can then be edited more quickly. When you are done working on this smaller scale, you will need to bring up the Proxy settings menu again, and change the Scale factor back to the Original size so that all of your edits/work take affect on that original higher quality video on the timeline.
-
-To use this feature, select \texttt{Settings $\rightarrow$ Proxy settings} and change the Scale factor from Original size to your downsized choice. You can choose ffmpeg as the File Format and a choice of various codecs associated with that. A good choice is the default of mpeg which can usually be quite fast. In addition, to modify values for that codec, click on the wrench icon. When you have completed your choices, just click OK, and then the video tracks will be rendered. This may take some time, but previous proxy renders will be reused.
-The proxy videos will be added to your assets in a separate Proxy folder, and the video track edits will use the proxies.
-The assets in both the Media folder and Proxy folder will look proxied when dragged to the Viewer although the scale may be different.
-Proxy downsizing renders all loaded tracks, but only work on the $1^{st}$ video layer of any multi-layer media. Rendered proxy media is saved in the same directory as the original media.
-However, if you proxy your session, the clips do not get proxied to the Proxy folder, but if you Drag and Drop the clip from the Clip folder to the Viewer or the Timeline, you will see that it too is proxied.
-As usual, you can delete proxy files from the project or disk in the Resources window if you no longer want to retain them.
-And you can save your project either as proxied or not.
-
-You can also nest clips while in a proxied state, but you can not drag the proxied nested clips
-to the viewer or the timeline.
-If you create proxies for Nested clips they will be saved in \texttt{\$HOME/Videos} unless you modify that in
-\texttt{Settings $\rightarrow$ Preferences, Interface} tab, \textit{Nested Proxy Path}.
-
-There are two ways that the proxy files can be used, with or without input scaling. When the proxy is done without rescaling, the Mask, Camera and Projector automations are re-scaled accordingly. In this situation, the entire project will be re-sized so that the session is in the resized geometry. Not all plugins are useful when the project is rescaled, because the keyframe data must be in the original geometry. In this case, you can use the rescaler, by enabling \textit{Use scaler (FFMPEG only)}. This has the added advantage that the project size does not change and the proxy media is down-scaled as usual and up-scaled on read-in, which means the project editing is done in full scale. Since decoding is done on smaller video, there is a time savings, but all rendering is done full scale. The main reason for using \textit{scaler} is that it does not change the image coordinate data, so that automation and plugin parameters will be in the original project geometry. This is not as fast as the first option, but is a performance gain, and may be needed if you are using plugins that need coordinate data such as the Title plugin. As noted, the scaler only works on ffmpeg video formats.
-
-In the upper right hand corner of the main window, there is a toggle button to easily switch back and forth when you have a proxied file on the timeline. The icon is to the left of the FF icon. It will have the letter “P” as the icon for Proxy or if \textit{Using Scaler}, the letter “S”. \quad \includegraphics[height=\baselineskip]{proxy-01.png} \quad This quick switch is especially useful when editing and you need to see a better image temporarily.
-
-Screencast in figure~\ref{fig:proxy-02} shows the Use scaler checked so you can still use plugins and the original project size is kept. The Scale factor pull-down gives you available size options. Note the new media dimensions shown (partially covered). If the size is an odd number, 1 is added to make the dimensions both even numbers.
-
-In the case of the scaler checkbox, it will retain that setting for ease of use.
-
-\begin{figure}[htpb]
- \centering
- \includegraphics[width=0.6\linewidth]{proxy-02.png}
- \caption{Proxy settings dialog}
- \label{fig:proxy-02}
-\end{figure}
-
-There is also a convenient \textit{Beep on done volume} dial included so that you can work on other tasks until there is an audible notify of completion. The default volume is set to 0 for no audible notify.
-
-A good choice for proxy settings with 1080p source video is:
+Info on proxies in \nameref{sec:proxy}
-\begin{lstlisting}[numbers=none]
-Scale Factor: 1/4
-Use Scaler: unchecked
-File Format: FFMPEG - mpeg
-Video Preset:
-Compression: mpeg.mpeg
-Bitrate: 1800000
-Quality: -1
-Pixels: yuv420p
-\end{lstlisting}
-
-If you get errors for some videos, such as those with strange variable bit rate or some types of files made on a smartphone, a usually reliable alternative is to change the following parameters:
-
-\begin{lstlisting}[numbers=none]
-File Format: FFMPEG - mov
-Video Preset:
-Compression: mov.mov
-\end{lstlisting}
-
-Or if you want small files with high image quality, a File Format of m2ts is optimal. For example a 1 GB file can be reduced to 50 MB with scale $\frac{1}{2}$.
+Info on transcode in \nameref{sec:transcode}
-Checking the \textit{Auto proxy/scale media loads} results in any additional media loads to be automatically proxy scaled. However, single frame media such as PNG or JPEG \textit{stills}, can not be scaled to \textit{stream} media. If this type of media exists, you should \textit{use scaler}.
-If you get error messages when creating proxies, check the Video wrench settings. These usually default to values that are expected to work correctly for the \textit{File Format} and codec you selected but they can be changed and may result in errors. If you get an error message of \textit{check\_frame\_rate failed} followed by \textit{Error making proxy} in the popup Errors window, do just that and check the Frame rate value by going to the Resources window, Media folder, and use the right mouse button for the Info option for that specific media in question. You can change the frame rate in this window to a more codec acceptable value. Different codecs may have different legal values.
-
-More specific information on which plugins need to use scaler is provided here next. If the keyframe data uses coordinate data that is absolute, then the scaler should be used. If the data is normalized (like always $0-100\%$) then the proxy can be done without the scaler. The session geometry format, shown in \texttt{Settings $\rightarrow$ Format} as $width \times height$, is changed if the scaler is not used to cause all of the data to be in the reduced format. If this affects the plugin operation, then scaler should be used. Examples of plugins that need the scaler are: Title, AutoScale, Scale, ScaleRatio, and Translate. Most others are safe to use without scaling.
-
- This makes its so that you can save your project
-either as proxied or not.
-
-\textbf{Transcode}, an option under the Settings pulldown right next to the Proxy settings option, is a type of full resolution \textbf{1:1 Proxy}.
-The process of transcoding works directly from the resource; it is independent of the timeline.
-All of the loaded asset media will be converted, that is, rendered in the selected format and loaded onto the timeline.
-Menu choices besides the usual File Format and File Type include: \textit{Tag suffix} (to add to media filename), \textit{Remove originals from project}, \textit{Into Nested Proxy directory} (an option to have the file saved here instead of the location of the original media), and \textit{Beep on done} volume.
-
-The settings of the project have an effect, for example the dimensions are taken into account. The resulting files are also larger than if they were created directly with ffmpeg.
-Transcode works for videos with or without audio and even single frame files, like png's.
-If you have a video file that also contains audio, and you convert only the video, the original audio will stay on the timeline if do not check \textit{Remove originals from project}. Or vice versa if audio converted and not video.
-Multiple stream media will only transcode the first stream (this would be like the TV channel recordings in the United States).
-You will get an error message if you already have a transcoded file in the selected format with the same suffix name and try to transcode it again with a different selection made -- you will have to delete that file first. An example would be
-an already converted file that has both video and audio and now you request video only.
-
-The BIGGEST gain from using this is if you have media that is not \textit{seekable}, that is, you can play it from the beginning but can not move to another spot and have the audio or video play correctly. A video file with no keyframes makes seeking next to impossible, but then a Transcode generally adds these keyframes.
\section{Some Settings Parameter Values}%
\label{sec:settings_parameter_values}
+\index{cache}
\texttt{Cache} in \texttt{Settings $\rightarrow$ Preferences, Performance} tab is used to store images on the timeline. One 1080p frame uses about 10 MB. The default setting is 256 and this is enough for testing and running. However, why not use more memory if it is available. To experiment for testing a good number tuned to the way you use your computer, set the cache to 0, start up \CGG{}, load a typical media file, play it and run \texttt{top} on the command line in another window to see how much memory is being used. In the \textit{top} display, look at \textit{free} memory. Whatever your computer is not using, is a good number to use for cache. If you start other programs, or change the design of the session so that it uses a lot of frame storage, you may need to experiment again later and resize accordingly.
\section{General Crash Handling Tips}%
\label{sec:general_crash_tips}
+\index{crash handling tips}
This section is a handy guide for describing various kinds of software computer system failures. Only some of these various lockups or crashes can be dealt with. Hopefully, it will help to have some hints to know what kind of failure it is, or to save your work or to avoid future problems. For most of this, your user name must be root, although you can certainly try to see if it works for you when not root.
To create a specific 440 Hz tone, follow these steps. You can vary the length, use more channels, or change the frequency to a different desired value (figure~\ref{fig:aeval}).
+\begin{figure}[htpb]
+ \centering
+ \includegraphics[width=1.0\linewidth]{aeval.png}
+ \caption{Use Audio$\rightarrow$Render effect to set render parameter values and then that effect can be varied.}
+ \label{fig:aeval}
+\end{figure}
+
\begin{enumerate}
\item Make sure there is an armed audio track on the timeline, get into Cut and Paste mode, and highlight
a selection or define In/Out points where you want to insert the audio tone.
that to 1C|2C instead of the usual default of 1C.
\end{enumerate}
-\begin{figure}[htpb]
- \centering
- \includegraphics[width=1.0\linewidth]{aeval.png}
- \caption{Use Audio$\rightarrow$Render effect to set render parameter values and then that effect can be varied.}
- \label{fig:aeval}
-\end{figure}
-
\subsection{Camera supplied LUTs}%
\label{sub:camera_supplied_luts}
+\index{LUT}
A LUT, acronym for Look-Up Table, is a mathematically precise way of taking specific RGB image values from a source image and modifying them to new RGB values by changing the hue, saturation and brightness values of that source image. In other words, LUTs are used to map one color space to another. Some high-end cameras supply a .cube file to use as input. There are several different ffmpeg plugins included with CinGG for using Lut's. These are:
\subsection{Encoding into Dolby Pro Logic}%
\label{sub:encoding_dolby_pro_logic}
+\index{dolby pro logic}
Dolby pro logic is an easy way to output 6 channel audio from a 2-channel soundcard with degraded but useful results. Rudimentary Dolby pro logic encoding can be achieved with usage of some effects.
\subsection{Remove Interlacing}%
\label{sub:remove_interlacing}
+\index{interlacing}
Interlacing often exists on older video sources, such as camcorders, and was previously used in broadcast television. Playing this video results in jagged images on a computer monitor, but with \CGG{} you can use deinterlacing effects to solve this. After some experimentation, it has been determined that the FFmpeg \textit{F\_kerndeint} plugin seems to produce the best results with the least amount of fiddling. But some of the parameters described next are pertinent to other potential plugin usage.
\subsection{Time stretching audio}%
\label{sub:time_stretching_audio}
+\index{audio!time stretching}
It may appear that time stretching audio is a matter of selecting a region of the audio tracks, enabling recording for the desired tracks, going to\texttt{ Audio $\rightarrow$ Render Effect}, and applying \textit{TimeStretch}. In actuality there are 3 audio effects for time stretching: Time Stretch, Resample, and Asset info dialog.
projects / goodguy / cin-manual-latex.git / blobdiff